spacer spacer spacer spacer
Kaydon Bearings spacer spacer

800.514.3066

customer service
spacer
spacer

Kaydon part number codes

Reali-Slim® open & sealed bearings
Endurakote®-plated bearings
Reali-Slim® stainless steel bearings

Kaydon Reali-Slim® open bearings and sealed bearings, stainless steel bearings, and Endurakote® bearings are marked for complete identification with an (8) or (9) digit part number. Positions 1–8 identify materials, size, type, and precision. Position 9 (optional) identifies non-standard internal fit.
 

 spacer

 
Log in to access 3D models,
CAD files, and engineering software
 
Forgot password?  |  Register
Position 1 2 3 4 5 6 7 8 9 10–13
Nomenclature Material Series Size Type Separator Precision Internal fit DFAR compliance
Example K G 1 2 0 X P 0 L -USA
spacer spacer
Position 1—Material
  Races/balls Seals, shields
A AISI 52100 Steel One seal—PTFE
B AISI 52100 Steel Two seals—PTFE
D AISI 52100 Steel One shield
E AISI 52100 Steel Two shields
F AISI 52100 Steel One seal—Nitrile rubber
Lami-seal®
G AISI 52100 Steel Two seals—Nitrile rubber
Lami-seal®
H AISI 52100 Steel One seal—Nitrile rubber
J AISI 52100 Steel Two seals—Nitrile rubber
K AISI 52100 Steel No seals or shields
L AISI 52100 Steel Two seals & Endurakote® plating
M M-50 Steel No seals or shields
N AISI 52100 Steel No seals & Endurakote® plating
P AISI 17-4PH Steel Ceramic balls
Q AISI 52100 Steel No shields or seals
S AISI 440C Stainless Steel No seals or shields
T AISI 440C Stainless Steel One seal—PTFE
U AISI 440C Stainless Steel Two seals—PTFE
V AISI 440C Stainless Steel Two shields
W AISI 440C Stainless Steel Two seals—Nitrile rubber
X AISI 52100 Steel Ceramic balls
Y AISI 440C Stainless Steel Ceramic balls
Z Other  

 

Position 2—Standard series cross section (inches)
Open bearings
  Radial thickness   Width  
AA *.187 x .187 open bearing series - AA
A .250 x .250 open bearing series - A
B .312 x .312 open bearing series - B
C .375 x .375 open bearing series - C
D .500 x .500 open bearing series - D
F .750 x .750 open bearing series - F
G 1.000 x 1.000 open bearing series - G
Sealed bearings
  Radial thickness   Width  
JHA .187 x .250 sealed bearing series - JHA
JA .250 x .250 sealed bearing series - JA
JB .312 x .312 sealed bearing series - JB
JU .500 x .375 sealed bearing series - JU
JG 1.000 x 1.000 sealed bearing series - JG
* Smaller section applies when position 3 is alphabetic—see following explanations of positions 3, 4, and 5.

 

Positions 3, 4, & 5—Size (bearing bore)
Numeric characters
Nominal bearing bore in inches multiplied by ten

Alphabetic characters
"A" in position 3 in combination with "A" in position 2
denotes .187 x .187 series
"A" in position 3 in combination with "H" in position 2
denotes .187 x .250 series
"A" in position 3 in combination with "S" in position 2
denotes .187 x .312 series

Examples
040 = 4.0" bore
120 = 12.0" bore
400 = 40.0" bore
"10" following "AA" in positions 2 & 3 =
.187 x .187 series with 1.0" bore
"15" following "HA" in positions 2 & 3 =
.187 x .250 series with 1.5" bore

 

Position 6—Bearing type
A Angular contact single bearing (not ground for universal duplexing) type A bearing - angular contact single bearing
B Angular contact pair—duplexed back to back type B bearing - angular contact pair, duplexed back to back
C Radial contact type C bearing - radial contact
F Angular contact pair—duplexed face to face type F bearing - angular contact pair, duplexed face to face
T Angular contact pair—duplexed tandem type T bearing - angular contact pair, duplexed tandem
U Angular contact single bearing—ground for universal duplexing type U bearing - angular contact single bearing, ground for universal duplexing
X Four-point contact type X bearing - four-point contact
Z Other

 

Position 7—Separator
snap-over pockets, bearing separators
C Non-metallic composite, segmental, "snap-over" type
D Phenolic laminate, one-piece ring "snap-over" type
E Brass, segmental "snap-over" type
L Nylon, one-piece ring "snap-over" type
N Nylon, "snap-over" type
P Standard formed ring "snap-over" type (material—brass or non-metallic composite)
T Stainless steel, formed ring "snap-over" type
V Brass, formed ring, "snap-over" type
X PEEK, one-piece, "snap-over" pocket
circular pockets, bearing separators
G Nylon one-piece ring, circular pocket
H Phenolic laminate, one-piece ring with circular pockets
J Nylon strip separator, circular pockets
K Phenolic laminate, riveted two-piece ring
Q PEEK, one-piece ring, circular pocket
R Standard formed ring, circular pocket (material—brass or non-metallic composite)
U Stainless steel, formed ring circular pockets
Y Brass, formed ring, circular pockets
wire strip or segmental cage, snap-over pockets, bearing separators
M Formed wire, strip or segmental, "snap-over" type, ball in every pocket
W Formed wire, strip or segmental, "snap-over" type
full complement bearing separators
F Full complement bearing—no separator
S Helical coil springs
Z Other (toroids, slugs, spacer balls or others available)

 

Position 8—Precision
(ABEC specifications are per ABMA standard 26.2)
0 Kaydon precision class 1 per ABEC 1F
1 Kaydon precision class 1 with class 4 runouts
2 Kaydon precision class 1 with class 6 runouts
3 Kaydon precision class 3 per ABEC 3F
4 Kaydon precision class 4 per ABEC 5F
6 Kaydon precision class 6 per ABEC 7F
8 Other

 

Position 9—Bearing internal fit
A .0000 to .0005 clearance
B .0000 to .0010 clearance
C .0005 to .0010 clearance
D .0005 to .0015 clearance
E .0010 to .0020 clearance
F .0015 to .0025 clearance
G .0020 to .0030 clearance
H .0030 to .0040 clearance
I .0040 to .0050 clearance
J .0050 to .0060 clearance
K .0000 to .0005 preload
L .0000 to .0010 preload
M .0005 to .0010 preload
N .0005 to .0015 preload
P .0010 to .0020 preload
Q .0010 to .0015 preload
R .0015 to .0025 preload
S .0020 to .0030 preload
Z Other clearance or preload not specified above
Type X or C = diametral preload or clearance
Duplexed type A = axial preload or clearance
 
Note: Above internal bearing fits apply to unmounted bearings only.
Mounting fits can greatly affect final internal bearing fit.

 

Position 10–13—DFAR compliance
All Reali-Slim® bearings requiring compliance with Defense Federal Acquisition Regulations (DFAR) "Specialty Metals" and "the Restrictions on Acquisition of Ball and Roller Bearings" clauses will contain '-USA' in positions 10-13. If internal fit is not called out in position 9, it will also contain a dash.

Example #1: KG120XP0L-USA
Example #2: KG120XP0--USA

spacer spacer